In questi giorni ho fatto una serie di casini.
Siccome la slack del mio pc è dalla 11.0 o forse direttamente dalla 10.2 che non la reinstallo da capo, ma che la upgrado, ed essendo arrivato alla 12.2 con kde 4.2 i686 per dual core di ponce, questo week-end ho pensato male di fare un pò di pulizia dei pacchetti obsoleti.
Lancio da root il mio bel pkgtool, e comincio a eliminare tutti i vecchi pacchetti (es. compiz, emerald, vecchi kernel....)
Problema che al riavvio, kde 4.2 non parte più dandomi errore "kdeinit4 errore, contorlla l'installazione".
Poco male, reinstallo kde 4.2 ma la solfa non cambia.
Reinstallo kde 3.5.10 e come sopra, con la differenza che l'errore è kdeinit3 a non avviarsi.
Avendo tempo da perdere, salvo tutto sulle altre partizioni, formatto e reinstallo da capo. (Sa molto winsoziano questa operazione, ma dopo 5 anni me lo concedete un formattino per ripulire bene bene il sistema?)
Alla fine dopo aver ripristinato il tutto.... E funziona che è una meraviglia, quadagnando ben quasi 3 giga di spazio da venerdi!
Ma mi accorgo che non ho fatto il back up dei file di installazione e configurazione del bluetooth (e già la prima volta che lo installai, mi ricordo che ci avevo perso un mese intero.).
Installo i vari pacchetti, sembra funzionare più o meno tutto, e riavvio.
E quà nasce un problema enorme.
Non parte più la rete e nemmeno alsa. Il bello che appena avviata se do il comando ifconfig non mi visualizza niente di niente.
Però accetta un bel
Codice: Seleziona tutto
bash-3.1# ifconfig eth0 192.168.168.193 netmask 255.255.255.0 up
bash-3.1# route add default gw 192.168.168.192
bash-3.1# ifconfig
eth0 Link encap:Ethernet HWaddr 00:1f:c6:1d:3d:14
inet addr:192.168.168.193 Bcast:192.168.168.255 Mask:255.255.255.0
inet6 addr: fe80::21f:c6ff:fe1d:3d14/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7668 errors:0 dropped:0 overruns:0 frame:0
TX packets:5499 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10333219 (9.8 MiB) TX bytes:531602 (519.1 KiB)
Interrupt:22 Base address:0xe000
Codice: Seleziona tutto
bash-3.1# ifconfig lo 127.0.0.1
bash-3.1# ifconfig
eth0 Link encap:Ethernet HWaddr 00:1f:c6:1d:3d:14
inet addr:192.168.168.193 Bcast:192.168.168.255 Mask:255.255.255.0
inet6 addr: fe80::21f:c6ff:fe1d:3d14/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7722 errors:0 dropped:0 overruns:0 frame:0
TX packets:5576 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10337109 (9.8 MiB) TX bytes:553355 (540.3 KiB)
Interrupt:22 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:174 (174.0 B) TX bytes:174 (174.0 B)
Se provo a togliere i moduli mi da:
Codice: Seleziona tutto
bash-3.1# modprobe -r bluetooth
WARNING: /etc/modprobe.d/bluetooth line 5: ignoring bad line starting with 'ctrl'
FATAL: Module bluetooth is in use.
Codice: Seleziona tutto
eg 24 32bit mmio: [fe02c000, fe02cfff]
PCI: 0000:00:05.2 reg 10 io port: [c400, c407]
PCI: 0000:00:05.2 reg 14 io port: [c000, c003]
PCI: 0000:00:05.2 reg 18 io port: [bc00, bc07]
PCI: 0000:00:05.2 reg 1c io port: [b800, b803]
PCI: 0000:00:05.2 reg 20 io port: [b400, b40f]
PCI: 0000:00:05.2 reg 24 32bit mmio: [fe02b000, fe02bfff]
PCI: 0000:00:06.1 reg 10 32bit mmio: [fe020000, fe023fff]
pci 0000:00:06.1: PME# supported from D3hot D3cold
pci 0000:00:06.1: PME# disabled
PCI: 0000:00:08.0 reg 10 32bit mmio: [fe02a000, fe02afff]
PCI: 0000:00:08.0 reg 14 io port: [b000, b007]
PCI: 0000:00:08.0 reg 18 32bit mmio: [fe029000, fe0290ff]
PCI: 0000:00:08.0 reg 1c 32bit mmio: [fe028000, fe02800f]
pci 0000:00:08.0: supports D1
pci 0000:00:08.0: supports D2
pci 0000:00:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:08.0: PME# disabled
PCI: 0000:00:09.0 reg 10 32bit mmio: [fe027000, fe027fff]
PCI: 0000:00:09.0 reg 14 io port: [ac00, ac07]
PCI: 0000:00:09.0 reg 18 32bit mmio: [fe026000, fe0260ff]
PCI: 0000:00:09.0 reg 1c 32bit mmio: [fe025000, fe02500f]
pci 0000:00:09.0: supports D1
pci 0000:00:09.0: supports D2
pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:09.0: PME# disabled
pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0e.0: PME# disabled
pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0f.0: PME# disabled
PCI: 0000:01:07.0 reg 10 32bit mmio: [fdeff000, fdeff7ff]
pci 0000:01:07.0: supports D1
pci 0000:01:07.0: supports D2
PCI: 0000:01:0b.0 reg 10 32bit mmio: [fdefe000, fdefe7ff]
PCI: 0000:01:0b.0 reg 14 32bit mmio: [fdef8000, fdefbfff]
pci 0000:01:0b.0: supports D1
pci 0000:01:0b.0: supports D2
pci 0000:01:0b.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:0b.0: PME# disabled
pci 0000:00:06.0: transparent bridge
PCI: bridge 0000:00:06.0 32bit mmio: [fde00000, fdefffff]
PCI: bridge 0000:00:0e.0 io port: [8000, 9fff]
PCI: bridge 0000:00:0e.0 32bit mmio: [fdd00000, fddfffff]
PCI: 0000:03:00.0 reg 10 32bit mmio: [fa000000, faffffff]
PCI: 0000:03:00.0 reg 14 64bit mmio: [e0000000, efffffff]
PCI: 0000:03:00.0 reg 1c 64bit mmio: [f8000000, f9ffffff]
PCI: 0000:03:00.0 reg 24 io port: [7c00, 7c7f]
PCI: 0000:03:00.0 reg 30 32bit mmio: [fbfe0000, fbffffff]
PCI: bridge 0000:00:0f.0 io port: [7000, 7fff]
PCI: bridge 0000:00:0f.0 32bit mmio: [f8000000, fbffffff]
PCI: bridge 0000:00:0f.0 64bit mmio pref: [e0000000, efffffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
tracer: 772 pages allocated for 65536 entries of 48 bytes
actual entries 65620
ACPI: RTC can wake from S4
system 00:01: ioport range 0x1000-0x107f has been reserved
system 00:01: ioport range 0x1080-0x10ff has been reserved
system 00:01: ioport range 0x1400-0x147f has been reserved
system 00:01: ioport range 0x1480-0x14ff has been reserved
system 00:01: ioport range 0x1800-0x187f has been reserved
system 00:01: ioport range 0x1880-0x18ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x801 has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:0c: iomem range 0xf0000000-0xf3ffffff could not be reserved
system 00:0d: iomem range 0xcd200-0xcffff has been reserved
system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
system 00:0d: iomem range 0xfefff000-0xfefff0ff could not be reserved
system 00:0d: iomem range 0xdfee0000-0xdfefffff could not be reserved
system 00:0d: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0x100000-0xdfedffff could not be reserved
system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0d: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:0d: iomem range 0xfefff000-0xfeffffff could not be reserved
system 00:0d: iomem range 0xfff80000-0xfff80fff could not be reserved
system 00:0d: iomem range 0xfff90000-0xfffbffff could not be reserved
system 00:0d: iomem range 0xfffed000-0xfffeffff could not be reserved
pci 0000:00:06.0: PCI bridge, secondary bus 0000:01
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: 0xfde00000-0xfdefffff
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:0e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:0e.0: IO window: 0x8000-0x9fff
pci 0000:00:0e.0: MEM window: 0xfdd00000-0xfddfffff
pci 0000:00:0e.0: PREFETCH window: disabled
pci 0000:00:0f.0: PCI bridge, secondary bus 0000:03
pci 0000:00:0f.0: IO window: 0x7000-0x7fff
pci 0000:00:0f.0: MEM window: 0xf8000000-0xfbffffff
pci 0000:00:0f.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:0e.0: setting latency timer to 64
pci 0000:00:0f.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 01 index 0 mmio: [0, 0]
bus: 01 index 1 mmio: [fde00000, fdefffff]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 io port: [0, ffff]
bus: 01 index 4 mmio: [0, ffffffff]
bus: 02 index 0 io port: [8000, 9fff]
bus: 02 index 1 mmio: [fdd00000, fddfffff]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 io port: [7000, 7fff]
bus: 03 index 1 mmio: [f8000000, fbffffff]
bus: 03 index 2 mmio: [e0000000, efffffff]
bus: 03 index 3 mmio: [0, 0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/W].
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
GFS2 (built Nov 20 2008 22:30:39) installed
msgmni has been set to 1714
async_tx: api initialized (async)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:03:00.0: Boot video device
pcieport-driver 0000:00:0e.0: setting latency timer to 64
pcieport-driver 0000:00:0e.0: found MSI capability
pci_express 0000:00:0e.0:pcie00: allocate port service
pci_express 0000:00:0e.0:pcie03: allocate port service
pcieport-driver 0000:00:0f.0: setting latency timer to 64
pcieport-driver 0000:00:0f.0: found MSI capability
pci_express 0000:00:0f.0:pcie00: allocate port service
pci_express 0000:00:0f.0:pcie03: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xf9000000, mapped to 0xf8d00000, using 1536k, total 14336k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: protected mode interface info at c000:b6b0
vesafb: pmi: set display start = c00cb713, set palette = c00cb76e
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
amd74xx 0000:00:04.0: UDMA133 controller
amd74xx 0000:00:04.0: IDE controller (0x10de:0x036e rev 0xa1)
amd74xx 0000:00:04.0: IDE port disabled
amd74xx 0000:00:04.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007
Probing IDE interface ide0...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 1.00
Loading iSCSI transport class v2.0-870.
rdac: device handler registered
hp_sw: device handler registered
emc: device handler registered
alua: device handler registered
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2456]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver: 8.02.01-k7
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.7
Copyright(c) 2004-2008 Emulex. All rights reserved.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
stex: Promise SuperTrak EX Driver version: 3.6.0000.1
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
sata_nv 0000:00:05.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
sata_nv 0000:00:05.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:05.0: Using SWNCQ mode
sata_nv 0000:00:05.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 23
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 23
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: ST3500820AS, SD25, max UDMA/133
ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-8: ST3500820AS, SD25, max UDMA/133
ata2.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3500820AS SD25 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 2:0:0:0: [sda] Attached SCSI disk
scsi 3:0:0:0: Direct-Access ATA ST3500820AS SD25 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2
sd 3:0:0:0: [sdb] Attached SCSI disk
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
sata_nv 0000:00:05.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:05.1: Using SWNCQ mode
sata_nv 0000:00:05.1: setting latency timer to 64
scsi4 : sata_nv
scsi5 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 22
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 22
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7: MAXTOR STM380215AS, 4.AAB, max UDMA/133
ata3.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: HL-DT-ST DVDRAM GH20NS10, EL00, max UDMA/100
ata4.00: configured for UDMA/100
scsi 4:0:0:0: Direct-Access ATA MAXTOR STM380215 4.AA PQ: 0 ANSI: 5
sd 4:0:0:0: [sdc] 156301488 512-byte hardware sectors (80026 MB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sdc] 156301488 512-byte hardware sectors (80026 MB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 4:0:0:0: [sdc] Attached SCSI disk
scsi 5:0:0:0: CD-ROM HL-DT-ST DVDRAM GH20NS10 EL00 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 5:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
sata_nv 0000:00:05.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:05.2: Using SWNCQ mode
sata_nv 0000:00:05.2: setting latency timer to 64
scsi6 : sata_nv
scsi7 : sata_nv
ata5: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb400 irq 21
ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb800 bmdma 0xb408 irq 21
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ATAPI: ASUS DVD-E818AT, 1.02, max UDMA/100
ata5.00: configured for UDMA/100
scsi 6:0:0:0: CD-ROM ASUS DVD-E818AT 1.02 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 78x/78x cd/rw xa/form2 cdda tray
sr 6:0:0:0: Attached scsi CD-ROM sr1
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
Fusion MPT FC Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ohci1394 0000:01:0b.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[fdefe000-fdefe7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ehci_hcd 0000:00:02.1: PCI INT B -> Link[APCL] -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfe02e000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-smp ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.7-smp ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
isp1760 0000:00:08.0: PCI INT A -> Link[APCH] -> GSI 22 (level, low) -> IRQ 22
memory length for this resource is less than required
isp1760: probe of 0000:00:08.0 failed with error -12
ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 21
isp1760 0000:00:09.0: PCI INT A -> Link[AMC1] -> GSI 21 (level, low) -> IRQ 21
memory length for this resource is less than required
isp1760: probe of 0000:00:09.0 failed with error -12
Initializing USB Mass Storage driver...
usb 1-5: new high speed USB device using ehci_hcd and address 4
usb 1-5: configuration #1 chosen from 1 choice
usb 1-5: New USB device found, idVendor=0ace, idProduct=1215
usb 1-5: New USB device strings: Mfr=16, Product=32, SerialNumber=0
usb 1-5: Product: USB2.0 WLAN
usb 1-5: Manufacturer: ZyDAS
usb 1-6: new high speed USB device using ehci_hcd and address 5
usb 1-6: configuration #1 chosen from 1 choice
usb 1-6: New USB device found, idVendor=8086, idProduct=9500
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: Product: CE9500B1
usb 1-6: Manufacturer: Intel Corporation (UK) Ltd
usb 1-6: SerialNumber:
usb 2-1: new full speed USB device using ohci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c0001197cc0]
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: New USB device found, idVendor=05a9, idProduct=0518
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB Camera
usb 2-1: Manufacturer: OmniVision Technologies, Inc.
usb 2-2: new full speed USB device using ohci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: New USB device found, idVendor=0a12, idProduct=0001
usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-7: new low speed USB device using ohci_hcd and address 4
usb 2-7: configuration #1 chosen from 1 choice
usb 2-7: New USB device found, idVendor=1130, idProduct=6605
usb 2-7: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-7: Product: USB Remote
usb 2-7: Manufacturer: Ping-IT
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
raid6: int32x1 920 MB/s
raid6: int32x2 938 MB/s
raid6: int32x4 900 MB/s
raid6: int32x8 650 MB/s
raid6: mmxx1 2058 MB/s
raid6: mmxx2 3718 MB/s
raid6: sse1x1 2047 MB/s
raid6: sse1x2 3357 MB/s
raid6: sse2x1 3385 MB/s
raid6: sse2x2 4696 MB/s
raid6: using algorithm sse2x2 (4696 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
usbcore: registered new interface driver hiddev
input: Ping-IT USB Remote as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.0/input/input2
input,hidraw0: USB HID v1.10 Keyboard [Ping-IT USB Remote ] on usb-0000:00:02.0-7
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 424k freed
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
ACPI: Power Button (CM) [PWRB]
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
Linux video capture interface: v2.00
ov511: USB OV518 video device found
ov511: Device revision 1
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
ov511: Compression required with OV518...enabling
Linux agpgart interface v0.103
ck804xrom ck804xrom_init_one(): Unable to register resource 0x00000000ff000000-0x00000000ffffffff - kernel bug?
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
nvidia 0000:03:00.0: PCI INT A -> Link[APC6] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:03:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 180.29 Wed Feb 4 23:44:25 PST 2009
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
ppdev: user-space parallel port driver
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: Attached scsi generic sg1 type 0
sd 4:0:0:0: Attached scsi generic sg2 type 0
sr 5:0:0:0: Attached scsi generic sg3 type 5
sr 6:0:0:0: Attached scsi generic sg4 type 5
Found: PMC Pm49FL004
ck804xrom @fff80000: Found 1 x8 devices at 0x0 in 8-bit bank
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
forcedeth 0000:00:08.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
ACPI: Expecting a [Reference] package element, found type 0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
fan PNP0C0B:00: registered as cooling_device2
ACPI: Fan [FAN] (on)
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Bluetooth: Generic Bluetooth USB driver ver 0.3
Error: Driver 'isp1760' is already registered, aborting...
saa7130/34: v4l2 driver version 0.2.14 loaded
usb 1-5: reset high speed USB device using ehci_hcd and address 4
forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:1f:c6:1d:3d:14
forcedeth 0000:00:08.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
forcedeth 0000:00:09.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
phy0: Selected rate control algorithm 'pid'
zd1211rw 1-5:1.0: phy0
ov511: Sensor is an OV6630AF
forcedeth 0000:00:09.0: ifname eth1, PHY OUI 0x5043 @ 1, addr 00:1f:c6:1d:4e:42
forcedeth 0000:00:09.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
ACPI: I/O resource nForce2_smbus [0x1c40-0x1c7f] conflicts with ACPI region SM01 [0x1c40-0x1c45]
ACPI: Device needs an ACPI driver
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40
Error: Driver 'isp1760' is already registered, aborting...
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
HDA Intel 0000:00:06.1: PCI INT B -> Link[AAZA] -> GSI 20 (level, low) -> IRQ 20
HDA Intel 0000:00:06.1: setting latency timer to 64
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
saa7134 0000:01:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
saa7133[0]: found at 0000:01:07.0, rev: 240, irq: 17, latency: 32, mmio: 0xfdeff000
saa7133[0]: subsystem: 5168:0214, board: LifeView FlyTV Platinum FM / Gold [card=54,autodetected]
saa7133[0]: board init: gpio is 31400
input: saa7134 IR (LifeView FlyTV Plat as /devices/pci0000:00/0000:00:06.0/0000:01:07.0/input/input6
ov511: Device at usb-0000:00:02.0-1 registered to minor 0
usbcore: registered new interface driver ov511
ov511: v1.64 for Linux 2.5 : ov511 USB Camera Driver
usbcore: registered new interface driver zd1211rw
usbcore: registered new interface driver btusb
saa7133[0]: i2c eeprom 00: 68 51 14 02 10 28 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
tuner' 2-004b: chip found @ 0x96 (saa7133[0])
tda829x 2-004b: setting tuner address to 61
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
tda829x 2-004b: type set to tda8290+75
saa7133[0]: registered device video1 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
Adding 1076344k swap on /dev/sda4. Priority:-1 extents:1 across:1076344k
fuse init (API version 7.9)
EXT3 FS on sda2, internal journal
lp0: using parport0 (interrupt-driven).
lp0: console ready
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -101
ov511: No decompressor available
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
