connessione all'avvio

[HaVaNa7]

Ciao a tutti.
vorrei che il mio notebook si connettesse all'avvio automaticamente, ma non riesco a far funzionare la cosa.

ho settato il file rc.inet.conf in modo esatto seguendo la wiki ma niente, se digito iwconfig non è nemmeno associato all'ap,
l'unico modo di connettermi è passando i settaggi da shell:
iwconfig wlan0 mode managed essid dlink channel 6 ecc...

sapreste aiutarmi?

[JohnnyMnemonic]

Prova a postare i file che hai modificato

[HaVaNa7]

rc.inet1.conf

Codice: Seleziona tutto

# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").

# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.

# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.

# =============================================================================

# Config information for eth0:
IPADDR[0]=""
NETMASK[0]=""
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""

# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""

# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""

# Default gateway IP address:
GATEWAY="192.168.0.2"

# Change this to "yes" for debugging output to stdout.  Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"

## Example config information for wlan0.  Uncomment the lines you need and fill
## in your data.  (You may not need all of these for your wireless network)
IFNAME[4]="wlan0"
#IPADDR[4]="192.168.0.10"
#NETMASK[4]="255.255.255.0"
USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]=""
DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
#WLAN_ESSID[4]=dlink
#WLAN_MODE[4]=Managed
#WLAN_RATE[4]="54M auto"
#WLAN_CHANNEL[4]="auto"
WLAN_KEY[4]="30313233343536373839"
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="wext"
#WLAN_WPAWAIT[4]=30

## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0"              # Use a different interface name instead of
                                # the default 'eth4'
#IFNAME[4]="eth0:1"             # Set up an IP alias.
#HWADDR[4]="00:01:23:45:67:89"  # Overrule the card's hardware MAC address
#MTU[4]=""                      # The default MTU is 1500, but you might need
                                # 1360 when you use NAT'ed IPSec traffic.
#DHCP_TIMEOUT[4]=15             # The default timeout for the DHCP client to
                                # wait for server resonse is 30 seconds, but
                                # you might want a shorter wait.
#DHCP_KEEPRESOLV[4]="yes"       # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes"          # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes"           # If you don't want the DHCP server to change
                                # your default gateway
#DHCP_IPADDR[4]=""              # Request a specific IP address from the DHCP
                                # server
#WLAN_ESSID[4]=DARKSTAR         # An example of how you can override _any_
                                # parameter defined in rc.wireless.conf, by
                                # prepending 'WLAN_' to the parameter's name.
                                # Useful with multiple wireless interfaces.
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey"
                                # Some drivers require a private ioctl to be
                                # set through the iwpriv command. If more than
                                # one is required, you can place them in the
                                # IWPRIV parameter (separated with the pipe (|)
                                # character, see the example).
#WLAN_WPA[4]="wpa_supplicant"   # Run wpa_supplicant for WPA support
#WLAN_WPADRIVER[4]="ndiswrapper"# Tell wpa_supplicant to specifically use the
                                # ndiswrapper driver (if you leave this empty
                                # the 'wext' driver is used by default)
#WLAN_WPAWAIT[4]=30             # In case it takes long for the WPA association
                                # to finish, you can increase the wait time
                                # (defaults to 10 seconds)

wireless.conf

Codice: Seleziona tutto

# Wireless LAN adapter configuration
#
# Theory of operation : 
#
# The script attempts to match a block of settings to the specific wireless
# card inserted, the *first* block matching the card is used.
# The address format is "hwaddr", with * as a wildcard.
# 'hwaddr' is the unique MAC address identifier of the wireless card.
# The MAC address is usually printed on the card, or can be found via ifconfig.
# Some examples here use only half of the MAC address with a wildcard to
# match a whole family of cards...
#
# All the Wireless specific configuration is done through the Wireless
# Extensions, so we will just call 'iwconfig' with the right parameters
# defined below.
# Of course, you need to have iwconfig installled on your system.
# To download iwconfig, or for more info on Wireless Extensions :
#	http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html
#
# Note : you don't need to fill all parameters, leave them blank, in most
# cases the driver will initialise itself with sane defaults values or
# automatically figure out the value... And no drivers do support all
# possible settings...
#
# -- This is a modified '/etc/pcmcia/wireless.opts' script --
# -- I added sections for Prism/GT and Atheros based cards --
# --    (supported by the prism54 and madwifi drivers)     --
# --              16/sep/2004 * Eric Hameleers             --
#

VERBOSE=1

case "$HWADDR" in

## NOTE : Comment out the following five lines to activate the samples below ...
## --------- START SECTION TO REMOVE -----------9B:53:CC
## Pick up any Access Point, should work on most 802.11 cards
#*)
#    INFO="Any ESSID"
#    ESSID="any"
#    ;;
## ---------- END SECTION TO REMOVE ------------

00:21:5D:*)
	INFO="wlan0"
	ESSID="dlink"
	MODE="Managed"
	CHANNEL="6"
	RATE="auto"
	KEY="30313233343536373839"

# Here are a few examples with a few Wireless LANs supported...
# The matching is done on the first 3 bytes of the MAC address

# SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter 
00:04:E2:*)
    INFO="SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter"
    # ESSID (extended network name) : My Network, any
    ESSID="any"
    # NWID/Domain (cell identifier) : 89AB, 100, off
    NWID=""
    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
    MODE="Managed"
    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
    FREQ=""
    CHANNEL="7"
    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
    SENS=""
    # Bit rate : auto, 1M, 11M,54M
    RATE="auto"
    # Encryption key : 4567-89AB-CD, s:password
    # Example for 40-bit encryption:
    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
    # Example for 104-bit encryption (aka 128-bit WEP):
    #KEY="d5ad2f05abd048ecf10b1c80c7"
    KEY=""
    # RTS threshold : off, 500
    RTS=""
    # Fragmentation threshold : off, 1000
    FRAG=""
    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
    IWCONFIG=""
    # iwspy parameters : + 01:23:45:67:89:AB
    IWSPY=""
    # iwpriv parameters : set_port 2, set_histo 50 60
    IWPRIV=""
;;

# Multiband Atheros based 802.11a/b/g universal NIC cards
00:05:4E:*)
    INFO="Multiband Atheros based 802.11a/b/g universal NIC"
    # ESSID (extended network name) : My Network, any
    ESSID=""
    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
    MODE="Managed"
    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
    FREQ=""
    CHANNEL="7"
    # Bit rate : auto, 1M, 11M,54M
    RATE="auto"
    # Encryption key : 4567-89AB-CD, s:password
    # Example for 40-bit encryption:
    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
    # Example for 104-bit encryption (aka 128-bit WEP):
    #KEY="d5ad2f05abd048ecf10b1c80c7"
    KEY=""
    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
    IWCONFIG=""
    # iwspy parameters : + 01:23:45:67:89:AB
    IWSPY=""
    # iwpriv parameters : set_port 2, set_histo 50 60
    IWPRIV=""
    ;;

# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
00:60:1D:*|00:02:2D:*)
    INFO="Wavelan IEEE example (Lucent default settings)"
    ESSID="Wavelan Network"
    MODE="Managed"
    #RATE="auto"
    KEY="s:secu1"
    # To set all four keys, use :
    #KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
    # For the RG 1000 Residential Gateway: The ESSID is the identifier on
    # the unit, and the default key is the last 5 digits of the same.
    #ESSID="084d70"
    #KEY="s:84d70"
    ;;

# Cisco/Aironet 4800/3x0
# Note : MPL driver only (airo/airo_cs), version 1.3 or later
00:40:96:*|00:02:8A:*)
    INFO="Cisco/Aironet example (Cisco default settings)"
    ESSID="any"
    # To set all four ESSID, use iwconfig v21 and the same trick as above
    MODE="Managed"
    #RATE="11M auto"
    #KEY="d5ad2f05abd048ecf10b1c80c7"
    KEY="off"
    ;;

# Samsung MagicLan (+ some other PrismII cards)
# Note : Samsung binary library driver, version 1.20 or later
00:00:F0:*|00:02:78:*)
    INFO="Samsung MagicLan example (Samsung default settings)"
    ESSID="any"
    MODE="Managed"
    CHANNEL="4"
    RATE="auto"
    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
    #IWCONFIG="power on"
    ;;

# Raytheon Raylink/WebGear Aviator2.4
# Note : doesn't work yet, please use for debugging only :-(
00:00:8F:*|00:00:F1:*)
    INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
    ESSID="ADHOC_ESSID"
    MODE="Ad-Hoc"
    RATE="auto"
    IWPRIV="set_framing 1"
    ;;

# Old Lucent Wavelan
08:00:0E:*)
    INFO="Wavelan example (Lucent default settings)"
    NWID="0100"
    MODE="Ad-Hoc"
    FREQ="2.425G"
    KEY="off"
    ;;

# Netwave (Xircom Netwave/Netwave Airsurfer)
00:80:C7:*)
    INFO="Netwave example (Netwave default settings)"
    NWID="100"
    KEY="00"
    ;;

# Proxim RangeLan2/Symphony (what is the MAC address ???)
XX:XX:XX:*)
    INFO="Proxim RangeLan2/Symphony example"
    NWID="0"
    MODE="Master"
    CHANNEL="15"
    IWPRIV="setsubchan 1"
    ;;

# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
XX:XX:XX:*)
    INFO="NWN Swallow example"
    ESSID="session"
    KEY="0000-0000-00 open"
    ;;

# Symbol Spectrum24 setting (what is the MAC address ???)
XX:XX:XX:*)
    INFO="Symbol Spectrum24 example"
    ESSID="Essid string"
    ;;

# Generic example (decribe all possible settings)
*)
    INFO="Fill with your own settings..."
    # ESSID (extended network name) : My Network, any
    ESSID=""
    # NWID/Domain (cell identifier) : 89AB, 100, off
    NWID=""
    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
    MODE=""
    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
    FREQ=""
    CHANNEL=""
    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
    SENS=""
    # Bit rate : auto, 1M, 11M
    RATE=""
    # Encryption key : 4567-89AB-CD, s:password
    KEY=""
    # RTS threshold : off, 500
    RTS=""
    # Fragmentation threshold : off, 1000
    FRAG=""
    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
    IWCONFIG=""
    # iwspy parameters : + 01:23:45:67:89:AB
    IWSPY=""
    # iwpriv parameters : set_port 2, set_histo 50 60
    IWPRIV=""
    ;;
esac

aggiungo che desidererei usare il dhcp e che il gateway è 192.168.0.2

[conraid]

c'è un po' di confusione in quella configurazione

Per quello che vuoi fare tu basta configurare /etc/rc.d/rc.inet1.conf con queste opzioni

Codice: Seleziona tutto

FNAME[4]="wlan0"
USE_DHCP[4]="yes"
DHCP_KEEPRESOLV[4]="yes" #Questo lo lascio perché lo avevi anche tu, ma dipende se ti serve o meno
WLAN_WPA[4]="wpa_supplicant"

e poi configuri /etc/wpa_supplicant.conf per l'autenticazione

se il gateway è lo stesso server DHCP allora

Codice: Seleziona tutto

GATEWAY=""

altrimenti

Codice: Seleziona tutto

GATEWAY="192.168.0.2"

e metti

Codice: Seleziona tutto

DHCP_KEEPGW[4]="yes" insieme alle altre voci

rc.wireless.conf non serve più, retaggio storico

[HaVaNa7]

ti ringrazio ma uso chiave WEP, che faccio?

[JohnnyMnemonic]

Codice: Seleziona tutto

WLAN_KEY[4]="tuachiave"

[HaVaNa7]

ok allora avevo settato bene. ma comunque ancora non va.

ho settato cosi':

Codice: Seleziona tutto

# Default gateway IP address:
GATEWAY="192.168.0.2"

IFNAME[4]="wlan0"
#IPADDR[4]=""
#NETMASK[4]=""
USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]=""
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
WLAN_ESSID[4]=dlink
#WLAN_MODE[4]=Managed
#WLAN_RATE[4]="54M auto"
#WLAN_CHANNEL[4]="auto"
WLAN_KEY[4]="miachiave"
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="wext"
#WLAN_WPAWAIT[4]=30

se lancio iwconfig:

Codice: Seleziona tutto

wlan0     IEEE 802.11abgn  ESSID:"dlink"
          Mode:Managed  Frequency:2.437 GHz  Access Point: Not-Associated
          Tx-Power=15 dBm
          Retry min limit:7   RTS thr:off   Fragment thr=2352 B
          Encryption key:miachiave  Security mode:open
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

ora impazzisco!!

[conraid]

Premesso che wpa_supplicant gestisce anche chiavi WEP (guarda gli esempi in /usr/doc/wpa_supplicant-0.5.10/examples) dovresti provare a specificare manualmente canale e modalità dell'AP visto che con comando manuale hai detto che ti funziona. Cioè per esempio aggiungere
WLAN_CHANNEL[4]=6
WLAN_MODE[4]="Managed"
e così via

p.s.
Io preferisco wpa_supplicant perché essendo compilato con il supporto ad HAL, gestisce anche la connessione allo spegnimento e accensione delle periferiche (o inserimento se dongle usb)