Ciao.....allora
lsmod | grep ath da' :
Codice: Seleziona tutto
ath5k 119853 0
mac80211 153050 1 ath5k
ath 6820 1 ath5k
cfg80211 109656 3 ath5k,mac80211,ath
led_class 2037 1 ath5k
Quindi i moduli ci sono e da' ifconfig anche se non attiva (ifconfig -a) riesco a vedere il wifi come apparecchio,
ma se lo attivo
Codice: Seleziona tutto
bash-4.1# ifconfig wlan1 up
SIOCSIFFLAGS: Unknown error 132
Il pc è un portatile, ed ha un pulsantino che avvia il wifi, quando accendo il pc
durante la fase del caricamento del so, quando si arriva più o meno a quà la luce diventa blu(attiva):
Codice: Seleziona tutto
input: HP WMI hotkeys as /devices/virtual/input/input7
rtc_cmos 00:06: RTC can wake from S4
ACPI: Thermal Zone [TZS0] (36 C)
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: 00
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
acpi device:11: registered as cooling_device1
rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
Linux video capture interface: v2.00
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:0f/LNXVIDEO:00/input/input8
Linux agpgart interface v0.103
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Thermal Zone [TZS1] (40 C)
cfg80211: Calling CRDA to update world regulatory domain
uvcvideo: Found UVC 1.00 device CNF7047 (04f2:b091)
input: CNF7047 as /devices/pci0000:00/0000:00:04.1/usb2/2-2/2-2:1.0/input/input9
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 20 (level, low) -> IRQ 20
hda_intel: Disable MSI for Nvidia chipset
HDA Intel 0000:00:07.0: setting latency timer to 64
ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
ath5k 0000:07:00.0: setting latency timer to 64
ath5k 0000:07:00.0: registered as 'phy0'
ath: EEPROM regdomain: 0x67
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x67
phy0: Selected rate control algorithm 'minstrel'
Registered led device: ath5k-phy0::rx
Registered led device: ath5k-phy0::tx
ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
udev: renamed network interface wlan0 to wlan1
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
nvidia: module license 'NVIDIA' taints kernel.
il portatile è un Compaq CQ60 e non ho più di un disp. wireless
Come potete aiutarmi????
, ho dato un'occhiata in /etc/rc.d ma non ho trovato niente...